Home Rewiring in Mount Kuring Gai, Sydney
Compare home rewiring specialists in Mount Kuring Gai using ABN, profile, public review, and referral signals where available. Typical electrical rates in NSW range from $70–$130/hr.
1 Checked Home Rewiring Specialists in Mount Kuring Gai
How Much Does Home Rewiring Cost in Mount Kuring Gai?
The following cost estimates are based on industry averages for electrical work in NSW. Actual prices will vary based on the scope of work, materials required, and access. Always get 2–3 written quotes before proceeding.
Typical Range
$70–$130
/hr
Emergency Rate
$195
After-hours / urgent
Free Quotes
2–3
Always get multiple
Price estimates only. Confirm scope, timing, and final cost with your chosen tradie before work begins.
Ready for exact prices? Get 2–3 free quotes for home rewiring.
Get Free QuotesMaterials You'll Need for Home Rewiring
What a tradie typically uses for home rewiring, with current retail price ranges. Your tradie usually supplies these — the quote should itemise them.
- Twin & earth TPS cable 2.5mm² · 100m rollmultiple rollsabout $499
- Double power point (GPO) · eachper point$14.08–$62.16
- 8-way switchboard enclosure · eachusually included$87.24–$111
Rough materials total
$600–$672
Core items only — labour is on top (see cost guide above)
Price ranges sampled from major Australian hardware retailers (July 2026). Estimates only — quantities and final costs depend on your job. Always confirm inclusions in writing with your tradie.
Electrical Licensing Requirements in NSW
In NSW, electricians must hold a contractor licence from NSW Fair Trading. An Electrical Safety Certificate must be issued for all work.
Other Electrical Services in Mount Kuring Gai
Also looking for related electrical work in Mount Kuring Gai?
Frequently Asked Questions About Home Rewiring in Mount Kuring Gai
How much does it cost to rewire a house in Australia?
Home rewiring in Australia is charged at an electrician's hourly rate of $70 to $130, since a full rewire is quoted as a project rather than a fixed figure. Cable alone runs about $499 per 100 metre roll, power points around $29 each, and a new switchboard from about $99, on top of labour.
How long does it take to rewire a house?
A full rewire of an average house typically takes an electrician several days to over a week, since every circuit needs to be run through walls and ceilings, tested and connected to a new or upgraded switchboard. Older homes with brick veneer, no roof access or asbestos sheeting can extend the job.
Do I need a new switchboard when rewiring my house?
Most home rewiring jobs include a switchboard upgrade, since old fuse-based boards cannot safely handle the safety switches and circuit breakers required under current wiring rules. A typical 8-way switchboard enclosure costs roughly $87 to $111, and pairing it with new safety switches is standard practice on a full rewire.
How much does an electrician charge per hour in Australia?
Electricians typically charge $70–$130 per hour depending on the state and job type. After-hours and emergency callouts attract higher rates, often $150–$250/hr plus a callout fee of $80–$150.
Do I need a licensed electrician for all electrical work?
Yes — in Australia, all electrical work including new power points, light fittings, safety switches, and switchboard upgrades must be performed by a licensed electrician. The only DIY exception is replacing light globes.
What is a safety switch and do I need one?
A safety switch (RCD) shuts off power within milliseconds if it detects a fault, protecting against electric shock. Australian standards require safety switches on all power and lighting circuits. If your home doesn't have them, upgrading is a legal requirement when renovating.
How long does a switchboard upgrade take?
Most switchboard upgrades take about half a day (4–6 hours), with power off for 2–4 hours while the electrician swaps the board and tests each circuit. Allow a full day if new wiring runs are needed. Your electrician will also notify your distributor (e.g., Ausgrid, Jemena, Citipower).
What should a Certificate of Electrical Safety include?
A Certificate of Electrical Safety (CES) must describe the work performed, the licence number of the electrician, the address, and confirm the installation was tested and complies with AS/NZS 3000.