Wall Patching in Holland Park West, Brisbane
Compare wall patching specialists in Holland Park West using ABN, profile, public review, and referral signals where available. Typical plastering rates in QLD range from $45–$90/hr.
1 Checked Wall Patching Specialists in Holland Park West
How Much Does Wall Patching Cost in Holland Park West?
The following cost estimates are based on industry averages for plastering work in QLD. Actual prices will vary based on the scope of work, materials required, and access. Always get 2–3 written quotes before proceeding.
Typical Range
$45–$90
/hr
Emergency Rate
$135
After-hours / urgent
Free Quotes
2–3
Always get multiple
Price estimates only. Confirm scope, timing, and final cost with your chosen tradie before work begins.
Ready for exact prices? Get 2–3 free quotes for wall patching.
Get Free QuotesMaterials You'll Need for Wall Patching
What a tradie typically uses for wall patching, with current retail price ranges. Your tradie usually supplies these — the quote should itemise them.
- Plasterboard topping compound · 20kgx1$34.19–$73.34
- Plasterboard jointing tape · roll$6.28–$20.45
Rough materials total
$40.47–$93.79
Core items only — labour is on top (see cost guide above)
Price ranges sampled from major Australian hardware retailers (July 2026). Estimates only — quantities and final costs depend on your job. Always confirm inclusions in writing with your tradie.
Plastering Licensing Requirements in QLD
In Queensland, plastering work over $3,300 requires a QBCC licence under the Plastering trade category.
Other Plastering Services in Holland Park West
Also looking for related plastering work in Holland Park West?
Frequently Asked Questions About Wall Patching in Holland Park West
How much does it cost to patch a hole in a wall in Australia?
Patching a small hole or dent in a wall costs $45–$90 per hour for a licensed plasterer in Australia, with most minor jobs done in an hour or two including drying time between coats. Materials are cheap: topping compound runs about $63 per 20kg tub and jointing tape around $8.50 a roll for larger repairs.
Can you patch a wall yourself or do you need a plasterer?
Small nail holes and minor dents are an easy DIY job with a tub of topping compound, around $63 for 20kg, and some sandpaper. Larger holes, door handle punctures through to the stud cavity, or ceiling cracks are worth a licensed plasterer at $45–$90 per hour for a flush, invisible finish that matches the surrounding wall texture.
How do you fix a large hole in plasterboard?
A large hole needs a patch of new plasterboard cut to size, screwed or glued to a timber or metal backing piece behind the gap, then taped and finished with two to three coats of jointing compound sanded smooth between coats. Compound costs about $63 per 20kg tub and jointing tape around $8.50 a roll.
How much does gyprock repair cost in Australia?
Small hole repairs typically cost $80–$200. Repairing a large section of wall or ceiling ranges from $300–$800. Full room replastering can cost $1,500–$4,000+ depending on size and condition.
Do I need a licensed plasterer?
In most Australian states, plastering work over a certain threshold (e.g., $10,000 in Victoria) requires a registered building practitioner. For smaller jobs, using a licensed plasterer is still strongly recommended for quality and warranty reasons.
How long does gyprock repair take to dry before painting?
Plaster compound typically needs 24–48 hours to dry fully between coats, and a minimum 48–72 hours before painting. In humid conditions (common in coastal areas), allow extra drying time.
What's the difference between cornice cement and plaster?
Cornice cement is a pre-mixed adhesive/filler specifically for attaching and patching cornice. Plaster is the base compound for walls and ceilings. Each product has different drying times and finishing properties — using the wrong one is a common DIY mistake.
Can I plaster over existing tiles?
It's possible but not always recommended. A plasterer needs to ensure the tiles are soundly bonded, properly prepared with bonding agent, and the weight load is appropriate. Direct plastering over tiles is common for fire-rated walls.