Gyprock Installation in Golden Square, Bendigo
Compare gyprock installation specialists in Golden Square using ABN, profile, public review, and referral signals where available. Typical plastering rates in VIC range from $45–$90/hr.
1 Checked Gyprock Installation Specialists in Golden Square
How Much Does Gyprock Installation Cost in Golden Square?
The following cost estimates are based on industry averages for plastering work in VIC. Actual prices will vary based on the scope of work, materials required, and access. Always get 2–3 written quotes before proceeding.
Typical Range
$45–$90
/hr
Emergency Rate
$135
After-hours / urgent
Free Quotes
2–3
Always get multiple
Price estimates only. Confirm scope, timing, and final cost with your chosen tradie before work begins.
Ready for exact prices? Get 2–3 free quotes for gyprock installation.
Get Free QuotesMaterials You'll Need for Gyprock Installation
What a tradie typically uses for gyprock installation, with current retail price ranges. Your tradie usually supplies these — the quote should itemise them.
- Plasterboard sheet 10mm 2400x1200 · sheetper 2.9m² of wall$27.89–$96.59
- Plasterboard base coat 20kg · 20kg bag$40.48–$63.71
- Plasterboard topping compound · 20kg$34.19–$73.34
- Plasterboard jointing tape · roll$6.28–$20.45
- Stud adhesive · cartridge$18.62–$35.55
Rough materials total
$127–$290
Core items only — labour is on top (see cost guide above)
Price ranges sampled from major Australian hardware retailers (July 2026). Estimates only — quantities and final costs depend on your job. Always confirm inclusions in writing with your tradie.
Plastering Licensing Requirements in VIC
In Victoria, plastering as part of domestic building work over $10,000 requires a registered building practitioner. The VBA registers plasterers under the Domestic Builder (Unlimited) or (Limited) category.
Other Plastering Services in Golden Square
Also looking for related plastering work in Golden Square?
Frequently Asked Questions About Gyprock Installation in Golden Square
Is Gyprock the same as plasterboard?
Yes. Gyprock is CSR's brand of plasterboard, the way Americans say drywall. Standard 10mm sheets retail for roughly $11–$41 depending on size and grade, with wet-area, soundproof and fire-rated variants costing more.
Is Gyprock asbestos?
Modern plasterboard contains no asbestos. The risk in Australian homes built before 1990 is older fibro (asbestos cement) wall and ceiling sheeting that looks similar to plasterboard. If your home predates 1990, get suspect sheeting tested before sanding, cutting or demolition.
How much does gyprock installation cost?
Supplied, fixed and flush-jointed, plasterboard installation costs about $40–$60 per square metre in Australia. The sheets themselves are only $11–$41 each. Most of the price is the setting and sanding labour that determines whether walls look flat under paint.
How much does gyprock repair cost in Australia?
Small hole repairs typically cost $80–$200. Repairing a large section of wall or ceiling ranges from $300–$800. Full room replastering can cost $1,500–$4,000+ depending on size and condition.
Do I need a licensed plasterer?
In most Australian states, plastering work over a certain threshold (e.g., $10,000 in Victoria) requires a registered building practitioner. For smaller jobs, using a licensed plasterer is still strongly recommended for quality and warranty reasons.
How long does gyprock repair take to dry before painting?
Plaster compound typically needs 24–48 hours to dry fully between coats, and a minimum 48–72 hours before painting. In humid conditions (common in coastal areas), allow extra drying time.
What's the difference between cornice cement and plaster?
Cornice cement is a pre-mixed adhesive/filler specifically for attaching and patching cornice. Plaster is the base compound for walls and ceilings. Each product has different drying times and finishing properties — using the wrong one is a common DIY mistake.
Can I plaster over existing tiles?
It's possible but not always recommended. A plasterer needs to ensure the tiles are soundly bonded, properly prepared with bonding agent, and the weight load is appropriate. Direct plastering over tiles is common for fire-rated walls.