Plasterboard Installation in Booragoon, Perth
Compare plasterboard installation specialists in Booragoon using ABN, profile, public review, and referral signals where available. Typical plastering rates in WA range from $45–$90/hr.
1 Checked Plasterboard Installation Specialists in Booragoon
How Much Does Plasterboard Installation Cost in Booragoon?
The following cost estimates are based on industry averages for plastering work in WA. Actual prices will vary based on the scope of work, materials required, and access. Always get 2–3 written quotes before proceeding.
Typical Range
$45–$90
/hr
Emergency Rate
$135
After-hours / urgent
Free Quotes
2–3
Always get multiple
Price estimates only. Confirm scope, timing, and final cost with your chosen tradie before work begins.
Ready for exact prices? Get 2–3 free quotes for plasterboard installation.
Get Free QuotesMaterials You'll Need for Plasterboard Installation
What a tradie typically uses for plasterboard installation, with current retail price ranges. Your tradie usually supplies these — the quote should itemise them.
- Plasterboard sheet 10mm 2400x1200 · sheetper 2.9m²$27.89–$96.59
- Plasterboard base coat 20kg · 20kg bag$40.48–$63.71
- Plasterboard topping compound · 20kg$34.19–$73.34
- Plasterboard jointing tape · roll$6.28–$20.45
Rough materials total
$109–$254
Core items only — labour is on top (see cost guide above)
Price ranges sampled from major Australian hardware retailers (July 2026). Estimates only — quantities and final costs depend on your job. Always confirm inclusions in writing with your tradie.
Plastering Licensing Requirements in WA
In WA, plastering does not require a specific trade licence for non-structural work. Structural plastering may require building services registration.
Other Plastering Services in Booragoon
Also looking for related plastering work in Booragoon?
Frequently Asked Questions About Plasterboard Installation in Booragoon
Is plasterboard the same as Gyprock?
Plasterboard is the generic term for gypsum board, while Gyprock is a specific brand of plasterboard made by CSR, similar to how Kleenex is a brand of tissue. Tradespeople in Australia often say Gyprock out of habit even when installing a different brand like Boral or USG, since the products are functionally the same.
Should I use 9mm or 12mm plasterboard?
9mm plasterboard suits ceilings on closely spaced trusses and standard wall linings in most homes, while 12mm plasterboard is the sturdier choice for walls needing extra strength or wider stud spacing. Wet areas and garage walls often use the thicker 12mm sheet for better impact resistance and fire performance.
How much does plasterboard installation cost in Australia?
Plasterboard installation costs $45 to $90 per hour for a plasterer in Australia, with sheets themselves running $28 to $97 each depending on size and thickness. A standard room typically needs several sheets plus base coat, jointing tape, and topping compound, adding roughly $80 to $150 in material costs on top of labour.
How much does gyprock repair cost in Australia?
Small hole repairs typically cost $80–$200. Repairing a large section of wall or ceiling ranges from $300–$800. Full room replastering can cost $1,500–$4,000+ depending on size and condition.
Do I need a licensed plasterer?
In most Australian states, plastering work over a certain threshold (e.g., $10,000 in Victoria) requires a registered building practitioner. For smaller jobs, using a licensed plasterer is still strongly recommended for quality and warranty reasons.
How long does gyprock repair take to dry before painting?
Plaster compound typically needs 24–48 hours to dry fully between coats, and a minimum 48–72 hours before painting. In humid conditions (common in coastal areas), allow extra drying time.
What's the difference between cornice cement and plaster?
Cornice cement is a pre-mixed adhesive/filler specifically for attaching and patching cornice. Plaster is the base compound for walls and ceilings. Each product has different drying times and finishing properties — using the wrong one is a common DIY mistake.
Can I plaster over existing tiles?
It's possible but not always recommended. A plasterer needs to ensure the tiles are soundly bonded, properly prepared with bonding agent, and the weight load is appropriate. Direct plastering over tiles is common for fire-rated walls.