How Much Does power point installation Cost in Australia?
power point installation costs vary significantly across Australia depending on your state, the complexity of the work, and local market conditions. Typical electrical rates range from $70–$130/hr nationally. Use this guide to understand what to expect, how to compare quotes, and find verified local specialists near you.
power point installation Cost Guide Australia 2026
The following pricing is based on national industry averages. Costs may be 10–20% higher in capital cities (Sydney, Melbourne) and lower in regional areas. Always get 2–3 written quotes before committing to any electrical work.
National Average
$70–$130
/hr
Emergency / After-Hours
$195
Estimated peak rate
Quotes Recommended
2–3
Before any work begins
power point installation Availability by State
NSW
679
listed
VIC
548
listed
QLD
527
listed
WA
262
listed
SA
204
listed
ACT
72
listed
TAS
70
listed
NT
45
listed
Prices are estimates only and may change without notice. Verify current pricing directly with your chosen contractor.
Find power point installation Specialists Near You
Browse verified electrical by city across Australia:
Electrical Licensing Requirements in Australia
Licensing requirements vary by state. Always verify your contractor holds the correct licence for your location.
Victoria
In Victoria, all electrical work must be performed by a licensed electrician registered with Energy Safe Victoria (ESV). A Certificate of Electrical Safety (CES) is required for all prescribed electrical work.
New South Wales
In NSW, electricians must hold a contractor licence from NSW Fair Trading. An Electrical Safety Certificate must be issued for all work.
Queensland
In Queensland, a QBCC Electrical Contractor Licence is required. All work must comply with the Wiring Rules (AS/NZS 3000).
Western Australia
In WA, electricians must be licensed with Electrical Inspections, Department of Energy, Mines, Industry Regulation and Safety.
South Australia
In SA, all electrical work must be performed by a licensed electrician. A Certificate of Compliance must be issued and lodged with SAPN.
Tasmania
In Tasmania, electrical contractors must be licensed under the Electrical Safety Act. A Certificate of Compliance is required for all work.
Australian Capital Territory
In the ACT, electricians must be licensed and all work must meet ACTPLA requirements.
Northern Territory
In the NT, electrical work requires a licence from NT Build and must comply with Australian Standard AS/NZS 3000.
Related Electrical Services
Also looking for other electrical services in Australia?
power point installation: Frequently Asked Questions
How much does an electrician charge per hour in Australia?
Electricians typically charge $70–$130 per hour depending on the state and job type. After-hours and emergency callouts attract higher rates, often $150–$250/hr plus a callout fee of $80–$150.
Do I need a licensed electrician for all electrical work?
Yes — in Australia, all electrical work including new power points, light fittings, safety switches, and switchboard upgrades must be performed by a licensed electrician. The only DIY exception is replacing light globes.
What is a safety switch and do I need one?
A safety switch (RCD) shuts off power within milliseconds if it detects a fault, protecting against electric shock. Australian standards require safety switches on all power and lighting circuits. If your home doesn't have them, upgrading is a legal requirement when renovating.
How long does a switchboard upgrade take?
A standard switchboard upgrade takes 4–8 hours. If your home needs new wiring runs or the switchboard is in a difficult location, allow a full day. Your electrician will also need to notify your distributor (e.g., Ausgrid, Jemena, Citipower).
What should a Certificate of Electrical Safety include?
A Certificate of Electrical Safety (CES) must describe the work performed, the licence number of the electrician, the address, and confirm the installation was tested and complies with AS/NZS 3000.
Can I add more power points to my home myself?
No. Adding power points involves working with mains power, which is illegal for unlicensed persons in all Australian states. An electrician can typically add a power point in 1–2 hours for $100–$250 per point.
Find a Electrical Near You
TradeRefer lists verified, ABN-checked electrical across Australia, ranked by real community referrals — not paid placement.
Browse Your Area